Major Problems with 2003 Mitsubishi Lancer Derived from Complaints & Recalls
Custom-fit Add-ons
Worst 3 complaints of 2003 Mitsubishi Lancer
2003 Mitsubishi Lancer
AUTOMATIC TRANSMISSION
Victims: 3
Mileage: 10224 miles
2003 Mitsubishi Lancer
FRONTAL
Victims: 2
Mileage: 13000 miles
2003 Mitsubishi Lancer
FRONTAL
Victims: 2
Browse 2003 Mitsubishi Lancer complaints by category
Problems with VISIBILITY, DEFROSTER/DEFOGGER/HVAC SYSTEM and AUTOMATIC TRANSMISSION are the most frequent issues recorded by the NHTSA from Mitsubishi Lancer owners.
Problem Category | Number of Problems |
VISIBILITY add my bumble bee to the growing list of lancers with broken off heater/a.c. knobs due to the badly designed... |
28
~ 69270 miles |
DEFROSTER/DEFOGGER/HVAC SYSTEM > VISIBILITY dt*: the contact stated the heating and cooling control knob fractured. the vehicle was taken to the service dealer who... |
28
~ 54861 miles |
AUTOMATIC TRANSMISSION > POWER TRAIN when i drive my 2003 mitsubishi lancer es at 20 mph and want to increase the speed and press the... |
19
~ 26009 miles |
CLUTCH ASSEMBLY > POWER TRAIN while driving at 55 mph vehicle experienced clutch failure and wouldn't accelerate.*ak... |
17
~ 19899 miles |
UNKNOWN OR OTHER paint chips and cracks easily tree sap and bird droppings eat through paint even if washed off within a few |
15
~ 20933 miles |
ELECTRICAL HEATING ELEMENT > WINDSHIELD > DEFROSTER/DEFOGGER/HVAC SYSTEM temperature control knob broke completely off. at first it was hard to turn and when it was switched over to... |
12
~ 41947 miles |
EQUIPMENT when i bought the lancer in 2003 the first thing i noticed was the knob for the air and heat... |
10
~ 49310 miles |
SUSPENSION while driving at 60 mph vehicle pulled to the right. vehicle was taken to the dealer who inspected it several |
8
~ 85775 miles |
ELECTRICAL SYSTEM sensor one had an internal failure. mitisubishi service tech stated it was due to the bad gas in north carolina.... |
7
~ 115286 miles |
FRONTAL > AIR BAGS vehicle was involved in a front passenger side collision while driving at 40 mph. upon impact neither driver's side nor |
7
~ 5857 miles |
VISIBILITY/WIPER purchased vehicle brand new july 2003. heat/ac knob has always been difficult to turn. it is now stuck on a/c.... |
6
~ 59170 miles |
POWER TRAIN at around 9500 miles the car began sticking slipping gears jamming into gear. it was diagnosed as a failed body... |
6
~ 82417 miles |
BODY > STRUCTURE i have the 2003 oz rally mitsubishi lancer and have had a problem right away with small paint chips occurring... |
6
~ 667 miles |
STRUCTURE tl*the contact owns a 2003 mitsubishi lancer. the contact stated that the top coat of clear paint is peeling off... |
5
~ 32802 miles |
VEHICLE SPEED CONTROL when driving at any speed vehicle revved then stalled. consumer contacted dealership on two separate occasions but the problem still |
5
~ 36604 miles |
MANUAL TRANSMISSION > POWER TRAIN at 1000 miles the clutch in my 03 lancer evo began to slip occasionally. i brought this to the attention... |
5
~ 9346 miles |
COLUMN > STEERING while driving steering wheel became loose and vehicle wobbled from four to six inches to either side. this happened three |
3
~ 71083 miles |
ENGINE ok ever since the gasket went bad and replaced the gasket on the lancer the catalytic converter has been giving... |
2
|
STEERING when driving my lancer either on city or highway it refuses to shift. the rpms go up but the car... |
2
~ 89000 miles |
AIR CONDITIONER > APPLIANCE > EQUIPMENT after purchasing my vehicle i noticed two things one that is troublesome and the other a major inconvenience. one day... |
2
~ 17500 miles |
INSTRUMENT CLUSTER/PANEL > ELECTRICAL SYSTEM when i bought the lancer in 2003 the first thing i noticed was the knob for the air and heat... |
2
|
HEATER CORE > DEFROSTER/DEFOGGER/HVAC SYSTEM > VISIBILITY the consumer experienced sudden acceleration . the consumer stated that when applying the brakes the vehicle accelerated. the consumer contacted... |
2
~ 29000 miles |
SERVICE BRAKES, HYDRAULIC when driving my vehicle the transmission does not shift gears properly. normal operation of the vehicle leads to jerky transitions... |
2
~ 750 miles |
TIRES yokohama avid p235/45r17 dot ehx8bem0803. consumer stated the tires wore out just on regular wear and tear . the tires |
2
~ 13270 miles |
SEAT BELTS i am a chemically sensitive individual having been poisened 9 years ago. i did not recoginize the hazards because the... |
2
~ 250 miles |
PEDAL/HAND LEVER(MOTORCYCLE) > CLUTCH ASSEMBLY > POWER TRAIN mitsu hq has circulated a service advisory to dealers to consider "any modification to vehicle for possible peripheral relationship to... |
2
~ 9000 miles |
AXLE ASSEMBLY > POWER TRAIN consumer called about having problems with the right front axle which broke while driving. the dealer and the manufacturer were... |
2
~ 50000 miles |
CRUISE CONTROL > VEHICLE SPEED CONTROL lancer oz rally edition: within 6 months of ownership noticed problems with cruise control occuring at any speed in which... |
2
~ 4000 miles |
EXTERIOR LIGHTING the air conditioning and heater controls knobs on dashboard. do not turn. can't. adjust temperature electrical cercuit in the emissions... |
1
~ 165000 miles |
HORN > ELECTRICAL SYSTEM airbag horn doesn't work i changed the clock spring but still doesn't work suspension is terrible i fell like i |
1
~ 137000 miles |
ELECTRONIC STABILITY CONTROL airbag horn doesn't work i changed the clock spring but still doesn't work suspension is terrible i fell like i |
1
~ 137000 miles |
CHECK VALVE > SUPPLY > SERVICE BRAKES, AIR on jan. 10 2011 i was driving my friends 2003 mitsubishi lancer. as we were leaving the doctors office parking... |
1
~ 80000 miles |
TREAD/BELT > TIRES tire located on passenger front side of vehicle is showing cracks between the tread area and the sidewall. four tires... |
1
~ 16539 miles |
COOLING SYSTEM > ENGINE AND ENGINE COOLING we have a 2003 mitsubishi lancer and the hot/cold switch broke off. in trying to research this i literally found... |
1
|
FUEL SYSTEM, OTHER 2003 mitsubishi lancer oz rally edition sudden acceleration car engine revs to 3000-4000 rpm. does not have abs so you... |
1
~ 100000 miles |
INTERIOR/UNDER DASH > WIRING > ELECTRICAL SYSTEM the heater knob on my mitsubishi lancer was hard to turn from hot to cold from the very first time... |
1
~ 65000 miles |
FUEL SYSTEM, GASOLINE tl*the contact owns a 2003 mitsubishi lancer. the service engine soon indicator light illuminated. the contact took her vehicle to... |
1
~ 46000 miles |
TIE ROD ASSEMBLY > LINKAGES > STEERING 2003 mitsubishi lancer. axle bearing failed on passenger side. i replaced it. inner tie rod tore out of outer tie... |
1
~ 100000 miles |
ACCESSORY SCISSOR/SCREW/BOTTLE JACK/LIFT > MECHANICAL > EQUIPMENT jack was on level surface jacked up the car to replace a flat after i began to put the spare |
1
~ 63000 miles |
FAN > COOLING SYSTEM > ENGINE AND ENGINE COOLING when i turn on the heat in my car the entire passenger side of the interior of my car floods..... |
1
|
ENGINE AND ENGINE COOLING 2003 lancer overheated and ran rough causing loss of coolant. mechanic determined there was a blown head gasket. *ts the |
1
|
FOUNDATION COMPONENTS > SERVICE BRAKES, HYDRAULIC our 2003 mitsubishi lancer es has only 15 520 miles on it and we've had to replace the front brake... |
1
|
REAR > SUSPENSION my 2003 mitsubisihi lancer oz is experiencing some type of problem with the rear suspension. we've had the car for... |
1
~ 45000 miles |
MASTER CYLINDER > FOUNDATION COMPONENTS > SERVICE BRAKES, HYDRAULIC slave cylinder suddenly went out. *nm... |
1
~ 20237 miles |
FRAME AND MEMBERS > STRUCTURE car had manual transmission problems roughly at 30k transmission problems again needed to be replaced not covered under warranty. car... |
1
|
REAR/OTHER > SEAT BELTS was in a 45 mph rear end collision. air bags did not deploy back seat passenger seat belt and tether... |
1
~ 28000 miles |
STRAP/WEBBING > TETHER > CHILD SEAT was in a 45 mph rear end collision. air bags did not deploy back seat passenger seat belt and tether... |
1
~ 28000 miles |
RETRACTOR > FRONT > SEAT BELTS driver of 2003 lancer was thrown from vehicle due to failure of seat belt to restrain causing two severe skull |
1
|
BUCKLE ASSEMBLY > FRONT > SEAT BELTS driver of 2003 lancer was thrown from vehicle due to failure of seat belt to restrain causing two severe skull |
1
|
TRANSFER CASE (4-WHEEL DRIVE) > POWER TRAIN mitsubishi corp. problem with transfer cases with their evolution lancer viii....lso piss poor management trying to shift blame on consumer.... |
1
~ 2500 miles |
WINDSHIELD > VISIBILITY windshield weather stripe malfunctioned. as a result windshield became loose. consumer was concerned that windshield will fall out. the part |
1
~ 25000 miles |
PADS > DISC > FOUNDATION COMPONENTS brake pads manufactured by carbotech engineering http://www.carbotecheng.com manufacturer a brake pad for the 2003 mitsubishi lancer evolution that is sold... |
1
|
BELL HOUSING > CLUTCH ASSEMBLY > POWER TRAIN i recently purchased a evo8 in december there was 339 miles on it when i bought it. it was the... |
1
~ 2500 miles |
BUMPERS > BODY > STRUCTURE car is rusting on rear bumper supports car has less than 1000 miles on it and i have had it |
1
~ 950 miles |
ENGINE > ENGINE AND ENGINE COOLING brand new mitsubishi lancer evolution blows engine after 6 000 miles. said customer neglect buy cannot prove it. *la... |
1
~ 6900 miles |
IGNITION > ELECTRICAL SYSTEM while driving 2003 mitsubishi lancer evolution in a rainstorm i encountered a severe loss of acceleration multiple times. resulting in |
1
~ 1800 miles |
AUTOMATIC (ASC) > ELECTRONIC STABILITY CONTROL while driving steering wheel became loose and vehicle wobbled from four to six inches to either side. this happened three |
1
~ 4000 miles |
AIR BAGS request for recall information regarding air bag defects on 2003 mitsubishi lancers. ... |
1
|
CATALYTIC CONVERTOR > EMISSION CONTROL > EXHAUST SYSTEM 2003 mitsubishi lancer recall on the catalytic converter. consumer states that the recall was never done but mitsubishi states that... |
1
|
Torque wrench
-
EPAuto 1/2-inch Drive Click Torque Wrenc...
- Durable Ratchet Head: Made from Hardened treated Chrome Vanadium steel alloy (Cr-V) Corrosion-Retardant: Satin Finish. Made in Taiwan
- Easy Storage: A sturdy plastic storage case is included. Non-Slip Grip: Knurled handle
- Easy to Read: High...
-
LEXIVON 1/2-Inch Drive Click Torque Wren...
- PRECISE - Ships pre-calibrated to +/- 4% accuracy and ready to use. Include calibration certificate with traceable serial number.
- DURABLE - Reinforced ratchet gear head constructed from hardened, heat-treated Chrome Vanadium alloy steel.
- LONGEVITY -...
-
LEXIVON 1/2-Inch Drive Click Torque Wren...
- PRECISION - Ships pre-calibrated to +/- 4% accuracy and ready to use. Include calibration certificate with traceable serial number.
- DURABLE - Reinforced ratchet gear head constructed from hardened, heat treated Chrome Vanadium alloy steel.
- LONG-LASTING...
-
LEXIVON 3/8-Inch Drive Click Torque Wren...
- PRECISION - Ships pre-calibrated to +/- 4% accuracy and ready to use. Include calibration certificate with traceable serial number.
- DURABLE - Reinforced ratchet gear head constructed from hardened, heat treated Chrome Vanadium alloy steel.
- LONG-LASTING...
-
LEXIVON Inch Pound Torque Wrench 1/4-Inc...
- PRECISION - Ships pre-calibrated to +/- 4% accuracy and ready to use. Include calibration certificate with traceable serial number.
- DURABLE - Reinforced ratchet gear head constructed from hardened, heat treated Chrome Vanadium alloy steel.
- LONG-LASTING...
-
TEKTON 3/8 Inch Drive Micrometer Torque ...
- Includes 1-pc. 3/8 in. drive torque wrench; Storage case; Product manual with torque conversion chart
- Wrench emits a click that can be heard and felt when the preset value is reached
- Permanently marked, high-contrast dual-range...
Mechanic tool set
-
Crescent 180 Pc. Professional Tool Set i...
- The Crescent Professional Tool Set has a newly designed 72T quick release ratchet
- Carefully selected assortment of hand tools for most industrial, mechanical, and consumer applications
- Get incredible access from combination wrenches with narrow heads,...
-
Craftsman Mechanic Tool Set, 215 Piece, ...
- MINIMAL ARCH SWING: 72-tooth 1/4 in. and 3/8 in. Drive Ratchets produce a 5-degree arc swing. Ideal balance between access and durability.
- VERSATILE: Comprehensive set of 1/4 in., 3/8 in. Drive Sockets and Drive Tool...
-
Craftsman Mechanic Tool Set, 230 Piece w...
- TACKLE A VARIETY OF PROJECTS: Complete automotive jobs and general mechanic fixes with this heavy-duty, 230-piece all-in-one mechanic tool set
- OPEN AND CLOSE THE DRAWERS WITH ONE HAND as you work with a spring-loaded locking...
-
DEWALT Mechanics Tool Set, 1/4" & 3/8" &...
- 72 tooth count ratchet providing a 5 degree arc swing for maneuverability in restricted areas
- Anti-slip driver handle provides maximum comfort
- Housed in a durable carrying case with metal latches
- Full-polish chrome for corrosion resistance
-
DEWALT Mechanics Tools Kit and Socket Se...
- Socket sets include 72 tooth count ratchets which allow for a 5 degree arc swing for maneuverability in restricted areas
- Ratchets include a low profile directional lever to help reduce catch points and for easy...
-
Amazon Basics Mechanic's Tool Set with C...
- Mechanic tool kit and socket set for tackling multiple sizes and types of fasteners, especially nuts and bolts
- Includes a 201-piece set that combines most popular sockets, wrenches, hex keys, and screwdriver bits
- Both metric...
Tool box
-
TUFFIOM 8-Drawer Rolling Tool Chest w/Lo...
- LARGE STORAGE CAPACITY: The rolling tool chest is designed with 8 drawers and 1 bottom cabinet for storing tools, small equipment or other objects. And the bottom cabinet features side hooks for hanging tools like...
-
beyond by BLACK+DECKER BLACK+DECKER BDST...
- Sturdy + Stackable: Durable Auto-Lock Latches Make Connecting These Stackable Units Quick And Easy
- Quick Access: The Quick-Release On The Locking Latch Allows You To Easily Separate Each Module When Stacked For Quick Access To...
-
BIG RED ANTBD133-XB Torin 20" Portable 3...
- Heavy duty tool box is made of thick steel, with powder coat red paint finish, beautiful and easy to clean
- Measures 20.5" L x 8.5" W x 12" H, and is equipped with 3 drawers...
-
DEKOPRO 228 Piece Socket Wrench Auto Rep...
- HIGH QUALITY&STANDARDS:Forged from high-quality steel and finished in high-polish chrome,strength, durability, anti-corrosion protection.All the tools meet or exceed ANSI critical standards
- COMPLETE VARIETIES:Contains tools needed for most small repairs and basic DIY projects around the...
-
Torin 17-Inch Plastic Tool Box,3-Tiers M...
- Tough metal latches are solid and easy to open and close, with long use life
- Foldable three-tier tray provides you with more storage space and you can separate metric and imperial tools to take them...
-
CARTMAN 148 Piece Automotive and Househo...
- Comprehensive Tool Set: The Cartman 148-Piece Tool Kit includes all the crucial tools needed for everyday home repairs and maintenance, from cutting to tightening, measuring to hammering.
- Durable and Corrosion-Resistant: All tools in the kit...
Discussion